日韩精品内射视频免费观看,日本精品一区二区中文字幕,精品国产粉嫩一区二区三区,一区二区三区无码被窝影院

Welcome To Wuxi Yi Rui Machinery Co., Ltd. 中文 CN  英文 EN
Yi Rui Would Be Your Friend Forever, And You Work Together!
TEL:0510-83691239
Yi Rui Product List
Wuxi Yi Rui Machinery Co., Ltd.
Contact: Yu Haibo (0) 13861855788
Tel: 0510-83691239
Fax: 0510-83690239
Postal Code: 214155
Email: sales@wx-yr.com
Q Q: 451055015
Address: Yang Shan Town, Wuxi
NEWS INFORMATION
Position:Home > NEWS >

Hydraulic cylinder disassembly should pay attention to matte

(1) Before removing the hydraulic cylinder, the hydraulic circuit should be relief. Otherwise, when coupled with the cylinder tubing joints loosen; the circuit of the high-pressure oil will quickly ejected. Hydraulic circuit should first loosen the relief valve pressure relief, etc. The regulator hand wheel or screw, so that the pressure oil unloading, then cut off the power on or off the power source, so that the hydraulic unit is stopped.

(2) Should be disassembled to prevent damage to the top of the threaded rod, oil port thread and piston rod surface, cylinder inner wall. To prevent the piston rod and other elongate member bent or deformed, application support skids equilibrium placement.

(3) Due to the structure and size of the various hydraulic cylinders vary slightly different order of removal. Generally should let go of the two chambers of the cylinder oil, then remove the cylinder head, and finally dismantle the piston and piston rod. When removing the cylinder head, the card key card key type connection or snap ring use a special tool, prohibit the use of flat shovel; for flanged top of the screw cap must be allowed hammering or hard pry . When the piston and the piston rod extraction difficult, cannot be forced to play, we should identify the reasons for further disassembly.

(4) Before and after unloading to try to create conditions to prevent the hydraulic cylinder parts are dust and impurity contamination around. For example, should dismantle as much as possible in a clean environment; After disassembly all parts use plastic sheeting to cover, do not use cotton or other work covered with a cloth.

(5) Cylinder disassembly to carefully check, to determine which parts can continue to be used, which parts can be repaired before using it, which parts must be replaced.

(6) Of the parts must be carefully cleaned before assembly.

(7) Around the sealing device to be properly installed. When ① install o-ring, do not pull its permanent deformation degree, do not scroll side suit, it may distort the shape due to the formation and leakage. ② When installation y-shaped and v-ring, pay attention to the mounting direction, to avoid oil spills installed instead. On the y-ring, its lips to deal with the pressure of the oil chamber; in addition, yx-ring is also a distinction shaft or hole, do not install the wrong. v-ring made of a shape different support rings, seals and pressure rings, when the pressure ring compress the seal ring, bearing ring seal ring can be generated as the sky-shaped seal, the installation should be opening facing the sealing ring pressure oil chamber; adjusting the pressure ring, no leakage should be limited, non overextended, sealed to prevent too much resistance. ③ sealing means such as cooperation with the sliding surface, the assembly should be coated with an appropriate amount of hydraulic oil. O-ring and dust ring should be fully renewed ④ disassembled.

(8) Threaded fastener tightening should use special wrench, torque moment shall meet the standards.

(9) The piston and rod assembly shall try to measure the concentricity and straightness over the entire length whether the ultra-poor.

(10) Assembled piston assembly and movement should be no sense of resistance blocking uneven and so on.

(11) When the hydraulic cylinder to be installed on the host computer, must be added between the oil inlet fitting and fastening a good seal to prevent oil spills.

(12) According to the requirements of a good assembly, it should be reciprocated several times under low pressure to exclude cylinder gas.
 
Website ©2015 Wuxi Yi Rui Machinery Co., Ltd. Copyright ALL RIGHTS RESERVED
Contact: Yu Haibo (0) 13861855788 Tel: 0510-83691239 Fax: 0510-83690239 Postal Code: 214155 Email: sales@wx-yr.com Q Q: 451055015 Address: Yang Shan Town, Wuxi

Sweep

Concern

精品国产女主播在线观看| 亚洲 欧美 天堂 综合| 亚洲精品国产综合一线久久| 91精品久久久久久久人妻| 国产麻豆国精精品久久毛片| 日本韩国精品一区二区三区| 国产毛女同一区二区三区| 欧美亚洲综合图片第一页| 电影在线一区二区免费精品| 19禁成人无码午夜久久| 高潮喷尿在线观看18岁| 久操新免费视频在线观看| 日本一区二区三区在线欧洲| 国产精品久久久久久无码专区| 波多野结衣中文字幕一区二区三区| 精品久久久久精品三级18| 蜜日韩欧美一区蜜桃视频| 日本精品乱码一区二区三区| 韩国免费的一级无码毛片| 亚洲综合成人一区二区三区| 亚洲ⅴa中文字幕无码毛| 精品视频在线观看a成v人| av在线精品一区二区三区| 美女被操到流水在线观看| 国产成人久久精品二区三| 97在线视频对对碰视频| 亚洲色成人影院影音先锋| 亚洲一区二区三区电影在线| 无码少妇一区二区| 99在线儿免费观看视频| 小早川在线一区二区三区| 国产精品亚洲精品99久久| 亚洲一级av无码毛片新| 午夜精品久久久久久久无码 | 欧美a级片一区二区三区| 二十四小时日本在线视频| 亚洲一区二区三区偷拍女| 日本一区二区三区在线播放| 成人片男女做受在线观看| 亚洲精品无码久久千人斩| 久久国产精品久久久久久|